Ignition Distributor [Late Vanagon]

Ignition Distributor [Late Vanagon]

Standard Aftermarket
$101.95
Skip to product information
Ignition Distributor [Late Vanagon]
Product: 0-986-237-639-AM
Works With: 1986-1991
Manufacturer: Quality Aftermarket/Bosch
Availability: Only 1 Left in Stock!

$101.95

Does this part fit your vehicle? Log in to your account & update your profile!

This brand-new aftermarket ignition distributor is a vital component to the proper operation of your engine. It is responsible for delivering spark to each cylinder at just the right moment to ignite the fuel and air mixture.

With these vehicles becoming older by the day, we are seeing more and more poor running (and no-running) issues due to worn-out parts related to this area of the ignition system. Whether it is the distributor itself, the electronic "hall sender," or the lowly but critical cap and rotor, this complete unit will ensure this part of your system is up to snuff. Includes O-ring.

This part includes:
• New aftermarket distributor
• New hall sensor unit
• New distributor cap - Standard Aftermarket, or Deluxe Bosch
• New ignition rotor - Standard Aftermarket, or Deluxe Bosch

• New distributor drive O-ring

Important installation note: These new distributors are supplied with a relatively low-quality distributor cap and ignition rotor pre-installed. On occasion, the cap will have the incorrect firing order listed. The correct firing order for all flat-four VW engines is 1-4-3-2. Please install your ignition wires in this order. Failure to do so will cause your engine to misfire. Also, be sure that the ignition rotor is pressed firmly into place and bottoms out on the shaft. If the rotor is not fully seated, it may damage the cap (and itself) as it rotates. We highly recommend purchasing the deluxe bundle, which includes the very best quality Bosch cap and rotor.

  • 5 stars: 6 (67%)
  • 4 stars: 1 (11%)
  • 3 stars: 1 (11%)
  • 2 stars: 1 (11%)
  • 1 star: 0 (0%)
J
Jonatan W.
Distributor

'91 Carat hasn't been feeling well for quite a long time. I just couldn't find out why she seemed sluggish and loosing power. Last winter I replaced the distributor cap & rotoe along with new plug wires. Found no improvement in performance. The only thing left was the distributor. So I got you to send the entire package...cables, cap, rotor & distributor. Installed everything, set the timing and this puppy runs like a stalled cat! We'll at least like she should & better than she has in years. My order was packaged properly & shipped & delivered on time. THANKS GUYS!

K
Kent R.
REQUIRES AGGRESSIVE TIMING ADJUSTMENT

The quality and performance of this distributor is fine. I can't give it five stars because the typical high level of installation documentation from Go-Westy was mysteriously lacking. Upon installing in roughly the same position as the stock distributor with the Hall sender plug pointing at about the 10 o'clock position, I noticed that the rotor's alignment was about 20 degrees clockwise from the position of the OEM rotor. I roughly "timed" the distributor by comparing and matching when the hell sender window engaged the sensor on each. It was close enough to run the engine and then time it properly according to the "35 degree" template method. In other-other words, you can't follow the Bently manual that shows the rotor center aligned with the lock nut collar. Following that would break the motor if you tried to start it up. 1991 Vanagon GL

Hi Kent, we checked this part and it is indeed slightly different than the original distributor. They work, but you are correct that they will sit in a different position than the original when timed. However, any position the distributor sits in will never break the engine. It just won't start. We have sent these findings to the manufacturer and they are correcting the next batch. Safe travels out there!

H
Harry T.

worked great thanks

J
Jeff D.

Part did not seem to work very well. Reinstalled original distributor and van ran way better

Hi Jeff, we are sorry the replacement distributor didn't work for you. We have had excellent success with them. We are here to help you with a refund or exchange. All the best, GoWesty

A
Anonymous

Crank no start was a faulty Hall sensor. Drop in this baby and I'm good!

A
Axel H.
Work great

I Fallow the tutorial step by step, was easy and now feel like new engine and run alot better
Thanks

T
Thomas

Came as advertised. Though the numbering on the cap does not match what is existing on the older distributor

C
C T.W.
.

.

g
german c.
1990 vanagon stalled. Cranks as long as the battery is charged. Crank,crank,crank and no start.

I searched all over the internet to get some hints as to what was going on. I have a GoWesty engine installed 3 years ago, 2.45 I believe. I didn't suspect the engine. I suspected that the folks that replaced it did't recommend changing some of the parts that i think they should have. I wasn't skimping so I know that if they had asked I would have paid for the rebuild of whatever they recommended.

On to my problem with the engine no-start but cranked. I didn't want to spend too much time or money on trying some things on my own. I narrowed it down to the no-start problem being the Hall sensor. I ordered the Ignition Distributor, ~100 bucks, because it was half as much as the Hall sensor. Also, part of my decision, the distributor was easy to install. It fixed my problem and my van started right up.

In the future, if I want to replace the Hall Sensor on the old distributor I removed I may do that. Or I can save my money and buy the Fuel Injection Component Replacement Kit which is what I would like to do since it has lots of benefits to it. Read the benefits of it here: https://gowesty.com/blogs/article-library/full-story-the-gowesty-fuel-injection-component-replacement-kit.