Gifting has never been easier
Perfect if you're short on time or are unable to deliver your gift yourself. Enter your message and select when to send it.
Axle Hardware Bundle [Bus/Vanagon]
| Product: | CV-HW-BNDL |
|---|---|
| Works With: | 1968-1991 |
| Manufacturer: | Quality Aftermarket |
| Availability: | Good Stock |
If you are going to service your axles, this hardware bundle will make gathering the parts for the job easy. There are enough parts in this bundle to install four CV joints (Bus & 2WD Vanagon) or six CV joints (Syncro).
Works with: All 1968-79 Bus & 1980-91 Vanagon. Manual and automatic, 2WD and Syncro rear axles and CV joints. Also works with Syncro front inner CV joints.
Kit includes:
• (24 or 36) Twelve-point axle bolts
• (24 or 36) Serrated lock washers
• (1) Twelve-point hex bit socket
Fit note: Not for Eurovan vehicles.
Reference numbers can be OE part numbers, superseded part numbers, and compatible part numbers. We provide this information to help ensure you're getting the right part for your needs.
Proposition 65: This product may contain chemicals known to the state of California to cause cancer, birth defects, or other reproductive harm.
Product: 930-AXLES-MT-N-G
Works with: 1980-1991
Product: AXLE-RBLD-4WD
Works with: 1986-1991
Product: 251-521-101DK
Works with: 1986-1991
Product: 930-STUB-N-2
Works with: 1980-1991
Product: AXLE-RBLD-2WD
Works with: 1968-1991
Product: CV-JOINT-BNDL
Works with: 1968-1991
Product: 930-STUB-N
Works with: 1980-1991
Product: 40-2005
Works with: 1980-1991
Product: 251-407-271J
Works with: 1986-1991
Product: 251-501-203G
Works with: 1980-1991
Product: CV-BOOT-BNDL
Works with: 1968-1991
Product: 930-CVJOINT-GERMAN
Works with: 1980-1991
Product: 251-498-099E-REG
Works with: 1986-1991
Product: GW-CV-VSS
Works with: 1980-1991
Product: 211-501-265C-AM
Works with: 1971-1991
Product: 211-501-331B
Works with: 1968-1991
Product: 251-521-000-DK
Works with: 1986-1991
Product: 251-498-203F
Works with: 1986-1991
Product: GW-CV-BOOT-HNBR-KIT
Works with: 1968-1991
Product: GW-CV-VSS-RING-KIT
Works with: 1980-1991
Product: 930-BOOT-HNBR-KIT
Works with: 1980-1991
Product: 930-BOOT-FLANGE
Works with: 1980-1991
Product: REDLINE-GREASE
Works with: All Vehicles
Product: GW-V-UNDERRUN-SUPPORTS
Works with: 1986-1991
Product: 251-498-201A
Works with: 1986-1991
Product: 8MM-DRIVE-SOCKET
Works with: 1968-2000
Product: 930-BOLT-SET
Works with: 1980-1991
Product: GVW-251-407-133A-4
Works with: 1984-1991
Product: 251-501-131A
Works with: 1980-1991
Product: 251-521-101HW-KIT
Works with: 1986-1991
Product: 211-501-221A
Works with: 1968-1991
Product: RUBBER-FLAP-4WD
Works with: 1986-1991
Product: 211-501-357-3
Works with: 1968-1991
Product: GVW-251-407-195/271
Works with: 1986-1991
Product: 893-407-237-6
Works with: 1968-1991
Product: 251-407-671
Works with: 1980-1991
Product: 20MM-NYLOCK
Works with: 1986-1991
Product: 111-405-661
Works with: 1980-1991
Product: 16-2262-7
Works with: 1980-1991
Product: 113-517-279-2
Works with: 1968-1991
Product: N-015-371-1-6
Works with: 1968-1991
Product: N-012-548-2
Works with: 1980-1991
Product: 930-BOOT-CLAMP
Works with: 1980-1991
One of the axles sent was not made for an automatic and was the incorrect length. The shop who installed it had to scout out a replacement axle. Not sure what i ended up with after spending $392 to GoWesty. Slowed down the repair and i was heading out on a trip. I called before ordering to make sure i was ordering the correct cv axles. This shouldn't have happened.
Getting the hardware bundle is a great idea. Price was good and installation was easy.
I received this set of CV fasteners, washers and the proper tool to install and torque the bolts. These are being used to secure the new DuroGreen CV boots I also received.
A+++ quality, fit and finish across the board for the lot. Looking forward to having long duration CV boots again.
Thank you Go Westy 🤙
All the one time parts needed for my Vanagon axle swap...I have a lifted camper so I changed the vw axles to Porsche non turbo 944 axles..... everything worked out great 👍
Nice kit to have on bus for spares
Great peace of mind knowing that all 24 are the same. Six of mine were overtighten 6mm hex, which 2 stripped. M8 12 point is da way to go, fo sho. Thx GW!
If you are replacing your axles, or taking them out to repack them I would advise new bolts, especially if yours are rusty.
Good
Well worth the price. It’s good to have fresh fasteners when replacing your CV axles.
Bolts and washers are perfect, tool makes install very easy!
Solid kit. Note: bolt heads omit serrated OEM edges. Pre grease makes for an easy install.
great for any suspension overhaul!
Gifting has never been easier
Perfect if you're short on time or are unable to deliver your gift yourself. Enter your message and select when to send it.